Forum: The Honda CA95 / Benly 150 Restoration
07-27-2014, 06:10 PM
|
Replies: 3
Views: 7,498
|
Forum: The Honda CA95 / Benly 150 Restoration
07-21-2014, 05:35 PM
|
Replies: 3
Views: 7,498
Starter quit working
This should be an easy fix and in the back of my mind I have a feeling how I should go about it but thought I'd post the question as I'm looking for a short cut.
Just finished the restoration and...
|
Forum: The Honda CA95 / Benly 150 Restoration
07-06-2014, 06:56 PM
|
Replies: 133
Views: 116,565
|
Forum: The Honda CA95 / Benly 150 Restoration
07-02-2014, 06:25 PM
|
Replies: 127
Views: 103,275
Well, the bike is done.
Took 6 months, so a...
Well, the bike is done.
Took 6 months, so a little sooner than expected.
This was a fun project and I learned a lot thanks to the folks on this site.
I really appreciate all the input, ideas,...
|
Forum: The Honda CA95 / Benly 150 Restoration
07-02-2014, 05:23 AM
|
Replies: 127
Views: 103,275
Kevin,
Yes :)
I apologize for not following...
Kevin,
Yes :)
I apologize for not following up sooner, but have been little busy with work.
The squeaks/rubbing I mentioned earlier were nothing more than the new brakes wearing in.
I installed...
|
Forum: The Honda CA95 / Benly 150 Restoration
06-14-2014, 06:50 PM
|
Replies: 133
Views: 116,565
|
Forum: The Honda CA95 / Benly 150 Restoration
06-04-2014, 07:40 PM
|
Replies: 127
Views: 103,275
it running
Its running and starts right off.no leaks but im getting squeeks. Seems after its ran a couple minutes something starts squeeking on the back wheel.
might just be the brakepads breaking in.? But I...
|
Forum: The Honda CA95 / Benly 150 Restoration
05-22-2014, 06:24 PM
|
Replies: 6
Views: 10,270
I had the same issue when replacing my rings...
I had the same issue when replacing my rings recently.
Was confused by the chrome vs. parkerized so I followed the below illustration putting the chamfer in the middle position.
Hope I did it...
|
Forum: The Honda CA95 / Benly 150 Restoration
05-18-2014, 01:48 PM
|
Replies: 127
Views: 103,275
Chip, Kevin...You guys are so smart! :)
Thank...
Chip, Kevin...You guys are so smart! :)
Thank you for the advise!!!
After taking the carb off and apart to check your suggestions It became apparent the idle screw was screwed too far in causing...
|
Forum: The Honda CA95 / Benly 150 Restoration
05-17-2014, 03:36 PM
|
Replies: 127
Views: 103,275
|
Forum: The Honda CA95 / Benly 150 Restoration
05-12-2014, 04:35 AM
|
Replies: 133
Views: 116,565
|
Forum: The Honda CA95 / Benly 150 Restoration
05-10-2014, 07:06 PM
|
Replies: 127
Views: 103,275
Well I found the problem, bad ignition switch....
Well I found the problem, bad ignition switch. Took it apart and cleaned the contacts but the bakelite backing crumbled putting it back together. Now the headlight works like a dream. Unfortunately...
|
Forum: The Honda CA95 / Benly 150 Restoration
05-10-2014, 09:55 AM
|
Replies: 127
Views: 103,275
|
Forum: The Honda CA95 / Benly 150 Restoration
05-09-2014, 03:22 PM
|
Replies: 127
Views: 103,275
|
Forum: The Honda CA95 / Benly 150 Restoration
05-09-2014, 02:03 PM
|
Replies: 127
Views: 103,275
Hi Guy's,
Thanks for all the replies, I will...
Hi Guy's,
Thanks for all the replies, I will fine tune that throttle some more.
In the meantime, I'm having a heck of time trying to track down why the headlight wont come on.
The horn works,...
|
Forum: The Honda CA95 / Benly 150 Restoration
05-04-2014, 03:02 PM
|
Replies: 127
Views: 103,275
Checked resistance on the cables and the switch...
Checked resistance on the cables and the switch and they were zero or close to it, so I figured it had to be a bad ground.
Scraped some of the new paint away from where the ground cable connects to...
|
Forum: The Honda CA95 / Benly 150 Restoration
05-03-2014, 02:11 PM
|
Replies: 127
Views: 103,275
|
Forum: The Honda CA95 / Benly 150 Restoration
04-30-2014, 04:52 PM
|
Replies: 127
Views: 103,275
|
Forum: The Honda CA95 / Benly 150 Restoration
04-28-2014, 07:20 PM
|
Replies: 127
Views: 103,275
|
Forum: The Honda CA95 / Benly 150 Restoration
04-26-2014, 06:06 PM
|
Replies: 127
Views: 103,275
Thanks you all.. I got it wired today.
I have...
Thanks you all.. I got it wired today.
I have an older wiring diagram so some of the wires were just a little bit different color and gave me a little challenge. Nothing a multimeter couldn't figure...
|